Benz

D, 1885 – 1926

(1) Benz & Co, Rheinische Gasmotorenfabrik, Mannheim, 1885 – 1899

(2) Benz & Cie, Rheinische Gasmotorenfabrik AG, Mannheim, 1899 – 1911

(3) Benz & Cie, Rheinische Automobil- und Motorenfabrik AG, Mannheim, 1911 – 1926

Karl Benz is honoured throughout the world as the man who designed and built the first workable motor car driven by an internal combustion engine. It is established that in 1885 his first Benz car was ready and made its first trials. Benz’s ideas were concentrated from the beginning on a car as an organic unit of chassis and engine, not on motorization of existing vehicles. The first Benz car was a three-wheeler with two driven rear wheels. The engine was a horizontal single-cylinder with a vertical crankshaft which had a horizontal flywheel. It developed ¾hp and a speed of 8mph is recorded for one of the first trial runs. This prototype Benz car had some featured which are still very extensively used in automobile construction: the water-cooled engine, electric ignition, mechanically operated inlet valve, and a differential gear. This first Benz car still exists and belongs to the Deutsches Museum, Munich, to which it was presented by its inventor. Several Benz Patentwagen replicas were built and are now in different museums.

Only a few Benz cars were produced and for sale in the following years. At the Munich Exhibition of 1888 Benz had the opportunity of showing his improved Benz car to a wider public. Instead of the wire wheels of the first Benz Patentwagen the later models had wooden-spoked wheels. Engine output was increased to 2hp. Sales of Benz’ stationary gas engines were quite satisfactory, while interest in Benz motor cars was very limited and it was not until 1890 that Benz started a real, if small, ‘to order’ production. This was partly a result of exhibiting his Benz car at the Paris World Fair in 1889 which led to increasing sales by his French agent Emile Roger, who already sold Benz stationary engines. The other important factor was that Benz was joined by two new partners in 1890. These two men who possibly saved Benz from the fate of numerous other inventors, driven aground by financial difficulties, were Friedrich von Fischer and Julius Ganss. Fischer took over internal administration and Ganss became responsible for sales. Benz himself was free for further developments on the technical side of the business, which made sound progress. 1893 saw the production of the first 4-wheeled Benz car, the Benz Victoria. This model was also the basis for the first Benz van and Benz bus in 1895; its technical conception was also adopted for the Benz Velo of 1894. This model has a place in the history of motoring as the world’s first production car. Production figures for 1885 to 1893 were 69 cars. 67 cars left the factory in 1894, mainly Benz Velos. These figures increased to 135 cars in 1895 and 181 in 1896.

In 1896 the first Benz Kontra-Motor appeared, an engine with two horizontally opposed cylinders. The first Benz lorry was produced in the same year. In 1898 pneumatic tyres were adopted for the Benz Comfortable. Production in 1899 was 572 cars, which brought Benz into the first rank of car producers. This number was surpassed in the following year with a production of 603 units. The first Benz racing car appeared in 1899 and was the start of numerus racing successes.

After 1901 sales of Benz cars declined as Benz stuck to his now outdated designs. Mercedes’ successes led him to evolve new concepts of construction; the result was the 2-cylinder front-engined Parsifal presented in 1903, available with cardan or chain drive and various engine outputs. In the same year a new 4-cylinder engine appeared and was used in all subsequent Benz models. A 1903 racing car developed 60hp and participated in the Paris-Madrid race. Karl Benz himself left the company in 1903 although he rejoined shortly afterwards. In 1906 he joined his sons in the firm of C. Benz Söhne.

1906 saw Benz gaining a second place in the Herkomer Trial while in the same event in 1907 a 5hp Benz finished first. Second and third place in the Coppa Florio, 1907, first place in the Florida 100-Miles Race, 1908, second and third place in the French Grand Prix, 1908, and second and fourth place in the American Grand Prix, 1908, led the world records which were set with 150hp and 200hp Benz cars by Bruce-Brown, Robertson, Oldfield and Hémery. With the 200hp Blitzen Benz Burman covered a mile in 25.4 seconds from a flying start at Daytona Beach in 1911. This was a speed of 140.8mph, but was not recognized internationally as a Land Speed Record.

In 1910 Benz acquired the Süddeutsche Automobil-Fabrik of Gaggenau. Production of private Benz cars in this factory was given up and in the following years Benz concentrated on commercial vehicles there.

A wide range of Benz cars for sale was marketed in the 1910-1914 period, ranging from the 2-litre Benz 8/20ps up to really big machines like the 10.1-litre Benz 39/100ps, all with side valve engines and shaft drive. However, the 22-litre Benz 200hp (which cost £1800 in England in 1912, and must have been the largest-engined private car to go on the market) had ohv and final drive by side chains. Benz were successful in the Austrian Alpine Trials, the Tatra-Adria Trial and various trials in Russia, to name only a few. The great promoter of German motoring, Prince Henry of Prussia, used only Benz cars.

The first Benz 6-cylinder car was produced in 1914 with the type Benz 25/65ps 6.5 litre. In 1918 the Benz 6/18ps 4-cylinder 1540cc appeared, a type developed during the war. A very important Benz development was the precombustion chamber diesel engine. It was first used in 1922 for Benz Sendling agricultural tractors, and the first diesel-engined lorry by Benz appeared in 1924. These were steps towards later Mercedes-Benz diesel-engined cars. Another idea introduced by Benz which also appeared in later Mercedes-Benz cars was the swing axle. It was one feature of the 2-litre 6-cylinder Benz ‘teardrop’ racing car designed on Rumpler principles. However, this car was not a great success either in its racing or in its sports version. In the Grand Prix of Italy in 1923 they gained fourth and fifth place. In 1924 Benz and Mercedes began to combine their interests, amalgamating in 1926.

Source: Georgano, encyclopedia of motorcar; HON

The information is written with the greatest of care. However, if you have any suggested amendments please contact us at office@prewarcar.com

Vulcan

GB, 1902 – 1928

(1) Vulcan Motor Manufacturing and Engineering Co Ltd, Southport, Lancs., 1902 – 1906

(2) Vulcan Motor and Engineering Co Ltd, Southport, Lancs., 1906 – 1928

The Vulcan car firm was better known for commercial vehicles. Private Vulcan cars stemmed from experiments conducted in the 1897-1899 period by the brothers Thomas and Joseph Hampson. A belt-driven single-cylinder voiturette Vulcan car with lateral radiators was shown in 1902, being replaced a year later by a 6hp Vulcan car with armoured wood frame, mechanically-operated inlet valves, and shaft drive. This Vulcan car was listed at only £105, and this Vulcan car was soon followed by a 10hp twin, also T-headed but with a steel frame, selling for £200. 4-cylinder Vulcan cars of 12 and 16hp, still modestly priced, were available in 1905, while the biggest 1906 Vulcan cars, with capacities of 3.1- and 5.2-litres, had gate change. No 2-cylinder Vulcan cars were catalogued after 1908, but a year previously Vulcan cars had joined the ranks of 6-cylinder manufacturers with a 4.8-litre T-headed machine featuring dual ignition and cone clutch, at £600 for a Vulcan car chassis. Unlike other makers, Vulcan cars retained their interest in this type, which Vulcan car had acquired a 4-speed box and had grown to 6-litres by 1908, and the 1909 Vulcan car range consisted of four 4-cylinder cars and the six, all shaft-driven and still with T-heads; the smallest Vulcan car, rated at 12hp, had a 3-speed gearbox and worm drive. A new 3.6-litre six Vulcan car with unit gearbox and worm drive followed in 1911, along with an L-head 2.4-litre fifteen. Worm drive was standardized on the 1912 Vulcan cars, when the bigger Vulcan cars had T-heads, and a 1.8-litre, 2-cylinder with an Aster engine was offered. All but the smallest Vulcan car had detachable wheels as standard in 1913, and by the outbreak of World War 1 the Vulcan car company was well established with a range of solidly-built Vulcan cars: a 2.4-litre 10/15, a 2.6-litre 15.9, and a 3-litre monobloc 15/20 Vulcan car at £375. All these Vulcan cars had L-heads and bull-nose radiators, though the similarly styled six retained the older Vulcan car configuration. A 1½-litre Vulcanette with a 3-speed rear-axle gearbox and full electrical equipment was announced for 1915 but the war intervened.

After 1918 the Vulcan car company concentrated increasingly on trucks, and a brief association with the Harper Bean Group (1919-1920) did no good to finances. Some odd experiments by Vulcan cars included a worm-drive 3½-litre V8 tourer Vulcan car intended to sell for £625 (1919), and two Vulcan cars in 1922 with Howard sleeve-valve engines, a big 3.6-litre sports-touring four Vulcan car and a 10hp 1.4-litre flat-twin listed at £315. However, none of these Vulcan cars reached the public, the regular Vulcan car lines being a 1.8-litre ohv 12 and a 2.6-litre sv 16/20, both with Dorman engines. There was also a conservative 20hp Vulcan carmodel with the Vulcan car company’s own 3.3-litre sv fixed-head engine and 4-speed separate gearbox, this Vulcan car was selling for £850 in 1921; by this time flat radiators were again being used on Vulcan cars. The Vulcan 20 was available to military order with full wireless equipment in 1923, in which year C.B. Wardman effected a liaison of Vulcan cars and Lea-Francis. The two companies pooled their dealer network, Vulcan cars became responsible for certain Lea-Francis power units and bodies, and Lea-Francis made gear and steering boxes for Vulcan cars. A 1½-litre sv Dorman-engined Vulcan 12 was listed at £295 in 1925, followed a year later by an ohv worm-driven derivative, also with Dorman engine, and looking very like a Lea-Francis. 4-wheel brakes were available on Vulcan cars in 1925 and standardized in 1926. Last of the line Vulcan cars were the 14/40 and 16/60, with the disastrous twin ohc 6-cylinder engines of their own make. Short-chassis Vulcan cars were worm-driven, but bevel drive was adopted for long-chassis versions. Vulcan cars wore artillery wheels, but were otherwise identical to their Lea-Francis counterparts which Vulcan cars were made alongside them at Southport. Not many of these Vulcan cars were made, and after 1928 only commercial vehicles were produced. The Vulcan car firm subsequently amalgamated with Tilling-Stevens and thus were abrorbed into the Rootes Group after World War 2. Truck production ceased in 1953.

US, 1913 – 1914

(1) Vulcan Motor Car Co, Painesville, Ohio, 1913

(2) Vulcan Manufacturing Co, Painesville, Ohio, 1913 – 1914

This Vulcan car was a cleanly-designed light car with a 27hp 4-cylinder engine. A two-seater speedster Vulcan car on an 8ft 9in wheelbase with electric lights sold for $750. A five-seater version of this Vulcan car with the same engine, but on a longer wheelbase, cost $850.

Source: Georgano, encyclopedia of motorcar; MCS, GMN    

The information is written with the greatest of care. However, if you have any suggested amendments please contact us at office@prewarcar.com