Lancia

Italy, 1906 to date

Fabbrica Automobili Lancia e Cia, Turin, 1906 to date

Vincenzo Lancia, the son of a wealthy soup manufacturer, was apprenticed to Ceirano in 1898 and went on to FIAT as chief inspector when that company took over the Ceirano factory in 1899. In July 1900 Lancia drove in his first race at Padua. Thereafter Lancia was a member of the FIAT team until 1908, making the running in the 1905 Gordon Bennett Cup and taking 2nd place in the 1906 Vanderbil Cup and the 1907 Targa Florio; but in 1906 he formed his own Lancia car company. Production of the first Lancia cars was halted by fire at the Lancia car factory in February 1907, but during the year the Alfa appeared as a 2½-litre 4-cylinder shaft-driven car with side valves in an L-head, a 4-speed gearbox and three-quarter elliptic rear suspension. A Lancia car chassis cost £400 in England. In 1908 there was a companion 3.8-litre 6-cylinder, the Di-Alfa, of which only 23 were made: Lancia was not to produce another Lancia car with a six for 42 years. Suprisingly enough, he did not race his Lancia cars, though Hilliard’s Lancia car won the 1908 Savannah race in America and two years later Billy Knipper won the Tiedeman Trophy on the same circuit with a Lancia car. These circumstances led to the introduction of a near-Lancia car, the SGV, to the American market in 1911: this Lancia car was sponsored by CV Tangeman, the former FIAT concessionaire in New York. Monobloc-engined Lancia cars made their début in 1909 with the 3.1-litre Lancia Beta, while capacity increased to 3.5-litres with the Lancia Gamma of 1910 and to 4.1-litres with the Lancia Delta of 1911, which had its waterpump mounted in one of the engine brackets. There was also a 2.6-litre 15hp Lancia car with a 4-speed rear-axle-mounted gearbox. Electric lighting was available on the 4.1-litre Lancia Eta at £757 in 1913. A year later full electrics (Lancia car company claimed to be the first standardized installation by a European manufacturer) came on the 4.9-litre Lancia Theta: the use of foot operation for the starter together with a cut-out gave the Lancia car five pedals, but in other respects it followed regular Lancia car practice with its 4 forward speeds and a dry multi-disc clutch. From 1911 the Lancia cars had 4-spoke steering wheels, and also the symbolic emblem of a lance, designed by Count Carlo Biscaretti di Ruffia for the Lancia car. During the World War 1 years, Lancia Theta derivatives served the Allied armed forces.

After the war the first Lancia car to came was the Lancia Kappa, an improved 90bhp development of the Lancia Theta with detachable head, but the shape of things to come was visible in an abortive 12-cylinder ohc 6-litre Lancia car which appeared at the 1919 Shows, though this Lancia car proved uneconomic to produce. The use of a very narrow-angle V of 22 degrees made a monobloc casting possible for Lancia cars. Though the Lancia Kappa gave place to the ohv Lancia Dikappa and to a 4.6-litre ohc V8, the Lancia Trikappa with conventional chassis, Vincenzo Lancia’s revolutionary Lancia Lambda was running in 1921, on show in 1922 and the Lancia Lambda was in full production by 1923. This Lancia car used once again a very narrow-angle V-type engine and overhead camshaft (though this time with only 4 cylinders, Lancia cars with the V4) which gave plenty of room for bodywork. Unitary construction was used for the standard torpedo body style of the Lancia car, this being available with a detachable hard top. The Lancia cars had independent front suspension of vertical-coil type, found on all Lancia cars until 1956 and persisting in the Lancia car range until 1963. Alloy blocks, pump cooling, full-pressure lubcrication, vacuum feed and 4-wheel brakes were also featured. 13.000 of these Lancia Lambda, in nine series, were sold up to 1931. Capacity of the Lancia Lambda went up to 2.4-litres in 1926 with the Lambda Seventh Series and again to 2.6-litres and 69bhp with the Lancia Lambda Eighth in 1928/ 1929. 4-speed gearboxes were standardized on the Lancia Lambda 5th series (1925). Separate chassis became an option with the Lancia Lambda 7th Series, being standardized on the Lancia Lambda 8th series and Lancia Lambda 9thseries; this last Lancia car series had coil ignition. Separate chassis have always been available as an option on subsequent chassisless Lancia cars. Though looked upon as a sports car in export markets by virtue of its superior handling, the Lambda Lambda car was never intended as such, and the later ‘long’ Lancia Lambda cars (11ft 2 7/8in wheelbase) made excellent taxicabs.

From 1929 Lancia marketed a series of ohc Lancia cars with separate chassis and hypoid final drive, of which the first was the Lancia Dilambda with a narrow-angle ohc V8 engine, electrically-welded frame, centralized chassis lubrication, fuel feed by twin electric pumps and (on later Lancia cars) servo brakes. Nearly 1.700 Lancia cars were made up to 1932. An 11ft 5in wheelbase was available for formal coachwork and a saloon Lancia car cost £1.295 in England.

To replace the Lancia Lambda in 1931 came two variations on this theme, the modest 1.9-litre 54bhp Lancia Artena, and the Lancia Astura, a small, 2.6-litre 73bhp V8 with silent 3rd gearbox, which had grown up by 1934 to 3 litres with servo brakes. By 1939 the Lancia car had acquired hydraulic actuation for these, had attracted some very elegant bodies from specialist coachbuilders and was the recognized transport for dignitaries of Mussolini’s Italy. A return to unit construction came with the little 1.2-litre Lancia Augusta late in 1932: this Lancia car was the usual ohc V4 with hypoid rear axle, but hydraulic brakes were standard on Lancia cars and its roadholding abilities compensated for a 65mph top speed and un-inspired looks. From 1933 to 1937 the Lancia Augusta was made in a French factory at Bonneuil, under the name Lancia Belna. Bodies were by French coach builders including Paul Née and Pourtout. In 1937 came Vincenzo Lancia’s last creation (he died that year), the 1.352cc Lancia Aprilia, which carried the Augusta formula of Lancia cars one step further, with independent torsion-bar rear suspension, a well-streamlined saloon body on the Lancia car, low weight (1.804lb) and engine output increased from 35 to 47bhp. No synchromesh was provided, but with a top speed of over 80mph and a fuel consumption of 30mpg this Lancia car became the exemplar of European light-car design. Capacity of the Lancia car went up to 1½-litres in 1939. The last Lancia Aprilia was made ten years later. Just before World War 2 came the 903cc Lancia Ardea, a miniature 29bhp version of the Lancia Aprilia with semi-elliptic rear suspension. Ten years later this Lancia car was given a 5-speed gearbox.

The first entirely new Lancia car since the founder’s death appeared in 1950. The Lancia Aurelia, the work of Vittorio Jano (late of Alfa-Romeo) and Gianni Lancia, retrained the hull, suspension and basic styling of earlier Lancia cars, but overhead camshafts had given way to a 1.754cc 56bhp push-rod V6, and the top 3 ratios of the back-axle gearbox were synchronized. 1951 Lancia cars were available with an optional 70bhp 2-litre engine and that year the first of the classic short-chassis Lancia GT coupé versions also appeared, with 2-litres and 80bhp. This Lancia car collected both 2nd place in the Mille Miglia and a class win at Le Mans. A 3rd in the Mille Miglia and a 1-2-3 victory in the Targa Florio followed in 1953. Rally wins recorde by later Lancia GT Aurelias included the Liège-Rome-Liège (1953), the Monte Carlo (1954) and the Acropolis as late as 1958. In 1953 Lancia car touring versions were available with 90bhp engines and there was also a seven-seater saloon Lancia car, the Lancia B15, on a 10ft 8in wheelbase, not to mention a 2½-litre 118bhp Lancia GT, which had acquired a De Dion rear axle by the end of the year. Steering-column change was standard on all coupés to the end of production in 1959, only the open Lancia Spyders coming with factory-fitted floor change. Meanwhile in 1953 the Lancia Ardea had given place to the 1.100cc Lancia Appia, a scaled-down Lancia Aurelia with a 38bhp engine. The cylinder block of the Lancia car was only 9½in long, a 2-bearing crankshaft being unusual with a 4-cylinder unit by this time. Though the Lancia Appia could exceed 75mph, the Lancia car was hardly competitive (at the equivalent of £780) with FIAT’s equally new 1.100-103 at £572. Encouraged by the success of the GT Lancia Aurelias, Lancia built some ohc sports-racing Lancia carversion which evolved into the 3.3-litre Lancia D24. Results were encouraging, a failure at Le Mans being balanced by a 3rd in the Targa Florio and a 1-2-3 victory in the Carrera Panamericanan (1953), and wins of Lancia cars in both the Targa Florio and the Mille Miglia in 1954. Less successful were the Jano-designed 2.5-litre Lancia D50s for Formula 1. These Lancia cars had 4-ohc oversquare V8 engines, space frames, double wishbone independent front suspension and 5-speed gearboxes mounted at the side of the differentials; their best performance was a 2nd place at Pau in 1955 and after Alberto Ascari was killed the whole Lancia car operation was disposed of to Ferrari. At the same time the Lancia family lost control of the Lancia car company.

Good seller though the Lancia Aurelia was, Lancia cars were no longer competitive with Fiat or the state-subsidized Alfa Romeo factory, and their 1958 sales were 8.794 Lancia cars to Fiat’s 169.532. 1956 had brought a revolution in the form of the Lancia Flaminia, still a 2.5-litre V6 with rear-axle gearbox and hypoid final drive, but incorporating not only a revised form of unitary construction but also coil-and-wishbone independent front suspension. The 6-light saloon bodywork of the Lancia car derived from the Lancia Aurelia-based Florda exhibited by Pininfarina at Turin in 1955. Standard engines in the Lancia car gave 98bhp, but by 1958 there were short-chassis GT versions with 125bhp and disc brakes were fitted on all Lancia Flaminia cars. Capacity of the Lancia car again went up to 2.8-litres in 1964, when the 3C sports coupé had 152bhp. Even more revolutionary was the Lancia Flavia of 1961, which Lancia car was the work of Dr. Fessia, designer both of the pre-war Fiat Topolino and of the CEMSA-Caproni, from which both its front wheel drive layout and ohv flat-4 engine were derived. Disc brakes, a 4-speed all-synchromesh gearbox and semi-elliptic rear suspension also featured in the specification of this Lancia car, and a 92bhp GT coupé model was available in 1962. 1.700cc bored-out versions of the Lancia car were already being offered by Nardi and in 1963 Lancia themselves offered an alternative 1.8-litre unit in their Lancia car. In 1964 the long-established Lancia Appia gave way to the Lancia Fulvia, which had much in common with the Lancia Flavia, though there was a reversion to an 1.100cc Lancia V4 engine. Sports Lancia car versions developed 71bhp and 106mph was claimed from the Lancia Fulvia GT. The 1967 Lancia Car Programme included standard and sporting models of the Lancia Fulvia. Flavia and Flaminia, with Kügelfischer fuel injection available on the Flavia. There was continuing support for GT racing and rally Lancia cars, the works team’s record in the latter field including two successive wins for Källström and Häggbom with Lancia cars (1969 and 1970) in the RAC Rally, and victories in the 1972 Monte Carlo and Moroccan events. A Lancia car specially designed for rallies was the Lancia Stratos HF coupé, powered by a mid-mounted Fiat 132 or Dino engine. A small production run of these Lancia cars was built in 1973. The Lancia Flaminia was not offered after 1970, but 1969 brought a 1.991cc version of the Lancia Flavia coupé with 131bhp and dual-circuit servo-assisted disc brakes. This Lancia car was followed by a 5-speed saloon model using a miniature replica of the old Lancia car grille. The 2-litre engine was standardized in all 1972 Lancia Flavias. Fulvias were available with 1.3-litre and 1.6-litre units, outputs of the Lancia car ranging from 85 to 114bhp.

Lancia – a firm which has the reputation of never having made a bad Lancia car- made a remarkable recovery in the early 1960s, and built 40.000 Lancia cars in 1966, but mounting debts forced them to sell out to Fiat in November 1969.

The first signs of integration of Lancia cars appeared in the new Lancia Beta model at the end of 1972. This fwd saloon was available with dohc 4-cylinder Fiat engines of 1.4, 1.6 or 1.8 litres, and LX versions of the Lancia car had automatic headlamp beam levellings.

Source: Georgano, encyclopedia of motorcar; MCS

The information is written with the greatest of care. However, if you have any suggested amendments please contact us at office@prewarcar.com

Morgan

GB, 1905 – 1906

Morgan and Co Ltd, Leighton Buzzard, Beds.

Made by a well-known firm of coachbuilders, the Morgan car was a conventional shaft-driven car with 5.8-litre T-head 4-cylinder Mutel engine, distinguished only by the Sparks-Boothby hydraulic clutch on the Morgan car, soon abandoned in favour of an ordinary leather cone. Only about five Morgan cars were made and their lack of success resulted in Morgan cars becoming Adler concessionaires in 1907, and abandoning motor manufacture.

GB, 1910 to date

Morgan Motor Co Ltd, Malvern Link, Worcs.

This Morgan car was the best-known, and best, of the British 3-wheelers that were popular while the horsepower tax gave the Morgan cars an advantage. H.F.S. Morgan’s tricycle was also the first of its type, this Morgan car going into production in 1910. At the front of a tubular chassis frame was an sv, air-cooled V-twin motor-cycle engine of 1.100cc by JAP, transversely mounted. Transmission of the Morgan car was by dog clutches and chains, providing two forward speeds. The steering was direct. The front wheels of the Morgan car, had independent front suspension, by sliding pillars and coil springs. There were two seats. A reasonable amount of power plus light weight meant an excellent performance of the Morgan cars. The Morgan car was safer than most 3-wheelers because its road-holding was above average. This recipe made the Morgan car popular with sportsmen, for whom the Morgan Grand Prix model was produced in 1914: the first catalogued competition Morgan car. Soon afterwards, an exiguous four-seater Morgan car, the forerunner of the Morgan Family model of the 1920s, was listed.

After World War 1, Morgan carscontinued to cater for all markets. Names changed, but the Morgan Sports or Morgan Standard model was the normal two-seater, also available in De Luxe form; the Morgan Family model was the more capacious type Morgan car, and the long-tailed Morgan Aero, later the Morgan Super Sports, was the Morgan car intended for serious speed work. Engines of Morgan cars were water- or air-cooled to choice, most being supplied by JAP, or by Blackburne in the case of the competition Morgan cars. From 1925 all the latter’s power units had overhead valves. By 1927 the Super Sports Morgan car could attain 80mph in standard trim, while the less sporting Morgan cars now had internal expanding front wheel brakes and electric starting. Geared-down steering and (if required) three forward speeds followed on Morgan cars in 1929. Even so, Morgan cars were losing customers to new, cheap sports cars such as the M-type MG. Three speeds and reverse in a normal gearbox (though still with chain final drive) were available from 1931 and standard on the Morgan car after 1932, and a modified 8hp Ford 4-cylinder engine could later be had in the Morgan car instead of the twin. Four years later the first 4-wheeled Morgan car was introduced, the excellent little Morgan 4/4. This Morgan car used an 1.122cc 4-cylinder Coventry-Climax engine with overhead inlet valves, developing 34bhp. The Morgan car was still light in weight, and retained the Morgan independent front suspension, so the performance and handling qualities of Morgan cars were well up to form. The Morgan car could attain 75mph. The twins were last catalogued in 1939.

Just before World War 2, a 1.267cc Standard 10hp engine with ohv head was substituted in the Morgan 4/4. When this was no longer available, from 1950, Morgan fitted a tuned Standard Vanguard unit in the Morgan car giving 70bhp. In this Morgan Plus Four, as the Morgan car was renamed, performance became still more lively, and when the 90bhp Triumph TR2 engine became available in 1954, maximum speed of the Morgan car rose to 100mph for the first time. With the advent of the Morgan Plus Four, there was no longer a small Morgan car, but this gap was made good in 1955, when the Morgan Series 2 4/4 arrived. This Morgan car used the very hard-wearing 1.172cc sv Ford Ten engine which had powered F4 Morgan. (The latter was the last 3-wheeler Morgan car, which had been made until 1950.) The result was a cheap, pleasant and reliable sports Morgan car of the old school. Later, the ohv Ford 105E engine was substituted. The latest version Morgan car had a 1.599cc 98bhp engine, a 4-speed all-synchromesh gearbox, front disc brakes, and the traditional Morgan suspension. The Morgan Plus Four kept pace with Triumph’s TR engine development, also acquiring disc brakes and, eventually, the 2.138cc 105bhp TR4 unit. A streamlined coupé, the Morgan Plus Four Plus of 1964, was a brief deviation from the classical Morgan car line which met with little approval and was discontinued after only 50 of these Morgan cars had been sold. When Triumph changed to a six during 1968, Morgan cars adopted a new engine for their bigger Morgan cars, and the Morgan Plus Four became the Morgan Plus Eight, powered by Rover’s 3 ½-litre 160bhp V8 and capable of 125mph. The 1973 versions of the Morgan car use the 4-speed all-synchromesh Rover gearbox in place of the Moss box previously fitted.

Source: Georgano, encyclopedia of motorcar; MCS, TRN

The information is written with the greatest of care. However, if you have any suggested amendments please contact us at office@prewarcar.com