Packard

US, 1899 – 1958

(1) New York & Ohio Automobile Co, Warren, Ohio, 1899 – 1901

(2) Ohio Automobile Co, Warren, Ohio, 1901 – 1902

(3) Packard Motor Car Co, Warren, Ohio, 1902 – 1903

(4) Packard Motor Car Co, Detroit, Mich., 1903 – 1955

(5) Studebaker – Packard Corp, Detroit, Mich., 1955 – 1958

The brothers J.W. and W.D. Packard bought a Winton in 1898 and determined to improve upon it. The result was the first 12hp Packard car of 1899. This Packard car followed traditional early-American lines with a single horizontal cylinder, central chain drive, buggy styling and wire wheels, but the Packard car was more advanced than its competitors in having a 3-speed and reverse gearbox and automatic spark advance. This gave way to the wheel-steered Model C Packard car, which proved capable of 40mph. An even more powerful Packard car, a single old for $3.000 in 1903 and on one of these Fetch and Krarup Packard cars successfully drove from San Francisco to New York in 61 days. In the same year a very big Packard car four of over 12 litres’ capacity was designed on European lines by Charles Schmidt, late of Mors. This Packard car sold for $7.500 and led to the famous Packard Model L, the first Packard car to bear the classic Packard radiator. This Packard car had side valves in an L-head and the gearbox was mounted in unit with the back axle; a similar engine was used in the racing car Gray Wolf, a streamlined lightweight Packard car capable of 75mph. 1906 Packard cars had T-head engines and magneto ignition in place of coil; engine capacity was 5¾-litres, increasing to 7-litres Packard cars in 1907 with the introduction of the famous ‘Packard 30’, from which 60bhp was claimed. For the next few years these high-quality four-cylinder Packard cars engaged all Packard’s attentions, the ‘Packard 30’ at $4.200 being joined by a short-wheelbase Packard 18 intended for use as a town carriage. Dry-plate clutches were adopted on Packard cars in 1910 and in 1911 a third model joined the range: Packard cars first six, the 7¼-litre ‘Packard48’.

Six-cylinder Packard cars only were offered in 1913, when electric lighting and starting were standardized. Spiral bevel final drive followed in 1914. Revolutionary was the world’s first series-production 12-cylinder, the Packard Twin-Six, which Packard car was announced in 1915 for 1916: this Packard car was also the first American touring car to use aluminium pistons and was quite modestly priced at $2.600. First series Packard cars had the unusual combination of left-hand drive and left-hand gear-change, abandoned on later series Packard car which also had detachable cylinder heads. A special racing car version of the Packard car, the 905 with a much bigger engine, recorded 149.9mph in the hands of Ralph de Palma at Daytona in 1919. From 1916 to 1920 only the Packard Twin Six was made, but this Packard car was then joined by a straightforward sv Single-Six selling from $2.350 up. This Packard car was given front-wheel brakes as standard replaced the Packard Twin-six during 1923; the Packard car came in two wheelbase lengths. A tourer Packard car cost $3.750 and it was the ancestor of the whole line of ‘Senior’ Packard cars up to 1939. 1925 Packard cars had centralized chassis lubrication and over 40.000 sixes were sold, as against less than 5.700 eights. Innovations on Packard cars for 1927 were a hypoid back axle, and a bigger 8-cylinder engine of 6.3-litres’ capacity, developing 106bhp. Only eight-cylinder Packard car were made in 1929, in which year a 5.3-litre Standard model was catalogued at $2.435, while in 1930 a limited series of ‘Packard 734’ sports models with high axle ratio, 145 bhp engines and 4-speed gearboxes was introduced. 1932 Packard cars had V-radiators. An inexpensive Packard Light 8 at $1.750, using the 5.3-litre engine, proved uneconomic to make, but there was also an excellent 7-litre V12 and all Packard cars had synchromesh gearboxes and vacuum-servo brakes. The Packard car company’s styling with its traditional radiator shape continued up to 1939. 

In 1935 the Packard car company made a bid for the low-priced market with the 3.7-litre straight-8 ‘Packard 120’ with hydraulic brakes and independent front suspension, priced from $980, as against $2.475 for the Packard Standard-eight, $2.990 for the Packard Super-eight and $3.820 for the Twelve. The new Packard car model accounted for 24.995 of the 31.889 cars sold by Packard cars that year and was joined two seasons later by a very similar 3.6-litre six, the ‘115’ at $860; this and the ‘120’, now enlarged to 4.6-litres, were made in a separate factory. In 1938, 50 percent of the Packard car company’s labour force was engaged in making the senior Packard cars which accounted for no more than 8 percent of total production.

In 1937 hydraulic brakes and independent front suspension were standardized on Packard cars throughout the range. 1939 was the last year of the true senior Packard cars; column change was introduced and overdrive was available on all Packard cars except the Twelve. Air conditioning was a 1940 option and 1941 brought the first of the handsome Packard Clipper line, made in 4-litre 6-cylinder and 4.6-litre straight-8 versions. Expensive Packard cars were still made, with custom bodywork by Rollson, Le Baron and Darrin available on the 5.8-litre chassis. During World War 2, body dies for the bigger, conventionally-bodied Packard cars were sold to the Soviet Government, the result being the 1945 Z.I.S.

Production of Packard cars was resumed with the Clipper 6 and 8 in 1946, but Packard never regained their former pre-eminence. Styling was unfortunate and the Packard car company retained the old straight-8 until 1954, though they evolved their own ‘Ultramatic’ automatic transmission in 1949 and had power brakes, steering and window lifts in 1954. Super-luxury Packard cars included the eight-seater Executive limousine at $6.900 in 1953 and the big Caribbean convertible.

The 1954 merger of Packard cars with Studebaker brought about a new 260bhp, ohv V8 with an ingenious inter-linked torsion-level suspension, while engines were sold to American Motors for their Nash and Hudson lines. Sales fell to a depressing 13.000 in 1956 and though the Packard lingered on until 1958, the last two seasons’ cars were nothing more than disguised Studebakers.

Source: Georgano, encyclopedia of motorcar; MCS

The information is written with the greatest of care. However, if you have any suggested amendments please contact us at office@prewarcar.com

Rover

GB, 1904 to date

(1) The Rover Co Ltd, Coventry, Warwickshire; Birmingham, 1904 – 1945

(2) The Rover Co Ltd, Solihull, Warwickshire, 1945 to date

The famous cycle firm Rover (which built J.K. Starley’s electric car in 1888) was offering tricars of conventional design in 1903, progressing from machines with cycle-type frames and belt drive to water-cooled and wheel-steered twins at £85 in 1905. The Rover car firm’s first production 4-wheeler was an interesting 8hp ‘single’ Rover car, the work of E.W. Lewis, which appeared in 1904. This Rover car had a tubular backbone frame, column change, a camshaft brake, and wire-and-bobbin steering, soon replaced by rack-and-pinion type. A smaller and less powerful 6hp Rover car followed at £105; one of the 8hp Rover cars was used by Dr. Jefferson in 1906 to drive from London to Constantinople.

The first 4-cylinder Rover car was a 16/20hp with shaft drive and 3.1-litre engine, followed by a small monobloc 10/12 Rover car. IN 1907 the shield-shaped radiator was introduced on Rover cars, vestiges of which survived until 1949. Courtis won that year’s TT on a 20hp Rover car of conventional design which was listed at a modest £400. The 8hp Rover car had acquired right-hand change by 1908, though the camshaft brake persisted, while in addition to the singles and the 20hp Rover car there were conventional L-head models of 1.6- and 2.5-litres in 1909. Rover cars own detachable wheels were optional in 1910, and in 1911 the 15hp 4-cylinder Rover car went over to pressure lubrication. Knight sleeve-valve engines were adopted, on an alternative version of the 8hp (this Rover car cost £30 more than its poppet-valve counterpart), and on a new vertical-twin 1.9-litre 12hp. 1912 was the last year of the singles and twins Rover cars, a new era arriving with the Clegg-designed 2.3-litre 4-cylinder monobloc 12hp Rover car at £350. This Rover car had worm-drive, inlet ports cast in the head, a water-jacketed carburetor, and electric lighting, and was the only Rover car model offered by 1914. It survived in the Rover car range until 1924, being known latterly as the Rover Fourteen. Later Rover cars had their headlamps attached to the radiator shell.

Rover car company built 12/16hp Sunbeams to War Department account between 1914 and 1918, but reverted to the small economy class in 1920 with a near-cyclecar, the Rover Eight, powered by a 1-litre (later enlarged to 1.130cc) flat-twin air-cooled sv unit, and retaining the 12hp Rover cars worm final drive. This Rover car was made under licence in Germany by Peter and Moritz. Some 17.000 Rover cars were sold up to 1925, prices dropping steadily from £300 to £160. Electric starters were not optional on Rover cars until 1923, and were never standardized. The successor Rover car was an ohv water-cooled in-line four, the 9/20, which Rover car cost £215, acquired front-wheel brakes in 1926, and was available with a detachable hartop coupé body in 1927, after which it gave way to a 1.2-litre Rover Ten, also with worm drive. 1929 Rover Tens had chromium plating, and sunshine roofs were available on closed models. A big 3½-litre six Rover car of 1924 did not go into production, but from 1925 to 1928 the Rover car company made some advanced 4-cylinder ohc Rover cars with 2.1- and 2.5-litre engines with hemispherical combustion chambers. Though the smaller 14/45 Rover car won the RAC’s Dewar Trophy for 50 consecutive ascents of Bwichy-Groes these wer expensive machines to make, and Rover cars breakthrough into bigger class came with a straightforward 2-litre ohv bevel-drive six which Rover car sold well at £410, and was developed into the stylish if not very practical Rover Light Six of 1930, noted for its raked screen and close-fitting cycle-type mudguards. This Rover car was the model which beat the ‘Blue Train’ in a race across France. The Rover car gave 70mph for £325. At the other end of the scale the same engine was made to propel a limousine Rover car on a 10ft 10in wheelbase.

V-radiators, lowered frames, and conventionally-mounted headlamps distinghuished the 1931 Rover cars, which ranged from the worm-driven Rover Ten at only £189 for a saloon up to the 2.6-litre, 60bhp Meteor 20 Rover car with prices from £398. This last Rover car was evolved into a pleasant 90mph sports model which Rover car won its class in the 1933 RAC Rally. 1932 saw the addition of a small six, the 1.4-litre Rover Pilot at £225, and an abortive experiment, the unconventional rear-engined 2-cylinder air-cooled Rover Scarab light car with all-round independent suspension, this Rover car intended to sell for £89. Though a cheap wormdriven Rover Ten was still listed in 1933, this was the year Rover cars adopted the free wheel, and turned to making Rover cars still in the medium-price class, but of generally superior quality – a position in the market Rover cars have held till the present day. 1934 Rover cars had 4-speed gearboxes, ohv engines, and spiral bevel final drive. The Rover car range consisted of a new 1.4-litre Rover Ten at £238, a 4-cylinder Rover 12 at £268, a 1.6-litre 6-cylinder Rover 14 derived from the earlier Pilot at £288, and a 16hp Rover Meteor saloon at £438, as well as 3-carburettor sporting sixes with 14 and 20hp engines. After a brief venture of Rover cars with hydraulic brakes, Rover cars reverted to mechanical actuation on all their Rover cars in 1936. Extensive restyling took place for 1937 on all Rover car models save the Ten, which Rover car was brought into line two seasons later. Big Rover cars were still offered: there was a 2.1-litre 16hp Rover car and a new 2½-litre Rover Speed 20 – and automatic chassis lubrication.

The 1937 style used on Rover cars lasted until the 1949 season. Changes included synchromesh in 1939, the replacement of wire wheels on Rover cars by disc types in 1940, a rationalization of the Rover car range after World War 2, and a switch to ioe engines in 1948, when only a 1.6-litre 4-cylinder 60bhp and a 2.1-litre 6-cylinder 75hp Rover car were offered, both with independently-sprung front wheels. Also new for Rover cars in 1948 was the 4x4 Land-Rover cross-country vehicle, initially using the 60hp engine; this Rover car has been progressively developed in 1950, but it was completely restyled, with slab-sided full-width bodywork, integral headlamps, steering-column change, and hydro-mechanical brakes, amended to full hydraulic two years later. The free-wheel of the Rover car was retained and the price was £1.106: this shape had a long production life which did not end till 1964. The range was widened once more in 1954 with a 2-litre four and a 2.6-litre 6-cylinder 90bhp version Rover car.

Meanwhile the Rover car company’s wartime work on gas turbines had led to the world’s first successful turbocar which appeared in 1950, using a 75 chassis and rearmounted 200bhp engine. The Rover car recorded 151,965mph over the flying kilometer in 1952, and was followed by further experimental cars of which the first designed as an entity was the T3, a 110bhp 4-wheel-drive Rover car coupé with fiberglass bodywork which was shown at Earls Court in 1956.

Development of the 1950 P4 Rover car  theme continued, with the introduction of overdrive (and the abandonment of the free-wheel) on the Rover 90 in 1956, and the adoption of vacuum servo brakes. There was a 105bhp version of the Rover 90, the Rover 105S, in 1957, and also an alternative model with Rover cars own 2-speed automatic transmission, dropped in favour of the Borg-Warner system after two seasons. Integral construction was introduced on the new 3-litre Rover car of 1959; this was a big Rover car with a 10ft 10½in wheelbase, and the option of overdrive or automatic, but retaining the overhead inlet valves of the smaller models. The price of this Rover car was £1.764. The 4-cylinder 60hp Rover car was dropped after 1962. From late 1959 all Rover cars had front disc brakes, and power-assisted steering appeared on the 3-litre in 1961.

In 1962 a new and more practical Rover turbocar appeared, the 140bhp T4 saloon with front-wheel drive and disc brakes on all 4 wheels: this Rover car did not go into production, though its structure served as a prototype for the advanced Rover 2000 of 1964, which first supplemented and then supplanted the last 2.6-litre developments of the old P4 Rover car, withdrawn at the end of that year. The Rover 2000’s 4-cylinder ohc engine developed 90bhp, all four forward gears were synchronized, a De Dion rear axle was used, an all 4 wheels of the Rover car had servo-assisted disc brakes. Like the 3-litre this Rover car had unitary construction, with detachable body panels, and its 100mph performance helped the Rover car to do well in rallies, with works support which had been initiated in the days of the 3-litre. The Rover-Leyland merger of 1966 brought the last of the major British independents under the control of the ‘big battalions’, but Rover car design was unaffected, and during the year there were two new versions of the Rover 2000, one with automatic, and the other Rover car, the TC with a 114bhp twin-carburettor engine. Engines provided the main news of 1967: the old ioe 2.6-litre six was adapted for use in the Landrover, and the Rover car company acquired a licence to build the discarded 3½-litre light-alloy ohv Buick V8, which powered a new edition of the 3-litre. This 3.5 was available only on Rover cars with automatic transmission, but on 160mph maximum speed was up to 108mph. A year later the V8 was wedded to the Rover 2000 structure to make the Three Thousand Five Rover car, a 114mph saloon, though this Rover car was not available with a manual gearbox until 1972.

The 8-cylinder Rover-Buick engine was to have further applications, among them Morgan’s Plus-8, an experimental mid-engined Alvis coupé, and the GKN-Lotus 47, a Europa derivative. In 135bhp form the unit also powered the Range Rover announced in June 1970 as a more luxurious station wagon development of the Landrover. This Rover car used rigid axles and coils all round. Other features were an all-synchromesh gearbox, permanently engaged 4-wheel drive, and all-disc brakes. Top speed was over 95mph. Range Rovers were used for a successful British Army expedition across the Darien gap in Central America in 1972. The Rover 2000, Three Thousand Five, 3.5-litre, Landrover comprised Rover’s 1972 – 1973 offerings.

Source: Georgano, encyclopedia of motorcar; MCS

The information is written with the greatest of care. However, if you have any suggested amendments please contact us at office@prewarcar.com